Here are some reliable benchmarks that follow everything that is written in this article. No tricks, less than $20, good lubrication, and some are built in.
2. RED Bones
3. Yellow jacket
(4) Suicide bomber.
Among skaters, whether they are on the road or downhill, it is common to think that it is the bearings that make the installation faster. Although it’s almost a complete myth, it’s good to know what to look for in the bearings you buy.
Some street skaters like to remove the panels from the bearings and let them pick up dirt and dust until they crackle as they roll. It’s not very good for the bearings, but at least they’ll work for a while. After all, bearings are just bearings, and as long as there is little lubricant and not enough dirt and dust to collect it, they will still work.
It is clear that some well lubricated and well-maintained ceramic bearings run faster on rainy days than the ones you use. However, Zack Maitum runs on mercury ball bearings in questionable condition, so does it really matter? Probably not. There are arguments for and against the direct correlation between driving quality and speed – it’s up to you to decide which side you’re on.
Bearings consist of 5 main parts: the outer race, the cage, the bullets, the inner race and the shield, which may or may not be on either side of the bearing.
As you can probably guess, theoretically the lower the resistance of the balls, the faster you can drive. A well-maintained bearing rolls easier than coarse dirt and dust; no one disputes that. The question is, how much does it cost to pay an extra dollar for expensive ceramics and other equipment that actually influences the trip?
The answer is almost zero; if you don’t participate in serious competitions, the difference will be minimal. It’s a good rule of thumb to hold on to bearings under $20 if you don’t sponsor them or if you don’t like them enough to raise extra money.
What is an ABEC classification?
The ABEC scale is the industry standard for ball bearing tolerances – the higher the number, the tighter the tolerances. The scale goes from 1 to 9, skipping even numbers. ABEC 5 has an error tolerance of 0.0035 mm, while ABEC 7 has an error tolerance of 0.0025 mm. If you can’t really make a difference until you drive, you’re probably the master. The ABEC scale does not measure the speed at which abearing can rotate.
The higher ABEC ratings are designed for use at very high speeds where smooth high-speed operation is required. When I talk about high speed, I mean they are used in airplanes, there is no reason to spend more money on ABEC 9 bearings on a skateboard.
Some brands, such as Reds and Zealous, don’t believe in ABEC ratings for skateboards, and you won’t see them on their packaging. Both brands are very reliable in the skating industry. Your products, even if they are not assessed by ABEC, are nothing but quality. There is also a trend to import bearing brands, if you have seen ABEC 11 (unbranded) bearings, you are selling something; there is no ABEC 11.
Which one is the best smartphone?
Lubrication is needed to make the bearings work. a good grease for your bearings will get them down quickly. It is a common mistake to use the wrong grease for the bearings; if the bearings are not sufficiently lubricated, make sure you use the correct grease. Keep away from wd-40, three-in-one grease, engine grease or heavy grease.
The bearings are provided with a fine, preferably non-aqueous lubricant to prevent the attracting of dirt. If you cannot find a good lubricant for the shoe bearings, you can use electronic grease or grease for sewage machines.
The best choice among longboarders for the best lubrication –Speed Cream by Bones.
What are mounted bearings?
Mounted bearings are a relatively new product on the scene and can be found in some of the best longitudinal bearings available. In contrast to conventional bearings, which require spacers and speed rings for normal operation, integrated bearings are integrated in. It is much easier to get the wheels in and out; turning the wheels takes less than half the time. I had a four man operation on a board with integrated elements like a pit stop in Formula 1, it only took a few seconds.
Storing your skating equipment is the key to safety, especially when skating on open roads. Don’t forget to regularly clean the bearings that get stuck in the equipment – it’s no fun.
Disclosure: We are a professional review company & our reviews are not biased towards any of the products we review. We test each product thoroughly and give marks to only the very best that is given by our author. We are very independently owned & the opinions expressed here are our own. However, if you purchase anything after clicking the links present in the articles then we get some commissions for it which help maintaining the websites expenses like servers, security etc.