We know how much you prefer longboarding. In order to ride properly, you must learn to keep your balance and stop on a longboard without falling or hurting yourself.
Remember that the first step to speed is to learn how to stop. If you’re new, you need to know how to prevent this by controlling your body.
There are several methods to stop on a longboard and it is enough to train enough.
We recommend that the starter wears protective equipment such as a helmet and elbow protectors. A sudden fall on a concrete surface without cushions can be a tough day.
How to stop at a longboard?
The wings go through your hair and you get the pump back and the speed of thrust is an incredible experience. You can slow everything down in different ways, from simple to advanced, from soft to progressive or from light to complex.
If you put your feet a little on the ground, you can stop as if by friction. It’s the easiest way to stop. Always be careful when you stop.
If you stop at high speed, you can fly in one direction and your longboard in the other. Consider which option you want to use to stop on a longboard, from the easiest to the most difficult routes:
First method: foot brakes.
Find out when to stop the brake pedal. At low speed only the brake pedal may be used. If you sit on a steep hill and want to drive in a curve, you have to walk from the sign. Follow this road to work easily at the level and at lower speeds.
Get ready for what you need. Don’t forget to wear the right shoes you need. Thin shoes and slippers are not recommended when the brake pedal is pressed.
An interruption caused by the slipping of your shoes on the floor will immobilize your longboard. This can damage your shoes and cause friction burns.
Keep your weight on your front leg. Start by keeping the maximum body weight on your forefoot. Which leg should you keep in front of you? It depends if you’re a stupid rider or an ordinary rider.
Don’t try to slow down your leg by leaning on your hind leg. As you descend the hills, leaning back divides your weight in the direction you move. That means your hind leg vibrates more than your front leg.
Raise your rear leg and pull it to the ground next to the sign. If you lean on your hind leg, you get off the board. Put some pressure on the floor to slide on it.
You should know that this could come out of your shoes and hurt your leg. Be sure to use wide shoes that can be towed over the ground.
Pull your shoes down to the ground. Slowly press down on the ground and slowly press forwards and backwards.
Press harder so you can stop quickly. However, be sure to set the scale to the desired speed to apply the weight.
Friction varies depending on the type of terrain. So, before you go skating, think about the weight needed to generate friction.
Second method: Force slip
Turning and cutting, sliding. A sharp bend until the sign is perpendicular to the road can make you stop.
Cutting off the toes on the side and pointing to the toe is one of the most natural shearing forces.
Watch every movement forwards or backwards.
Keep your weight on your heels and in front of the plate. When you have finished threading and setting up the Powerslide, divide your weight over the heels.
This means that you have to put your weight more on your back than on your front. Distribute the maximum weight, about 60-70% of your body, over the forefoot, which will help you to twist or fully glide.
If you put more weight on your hind leg, sliding will be more difficult. So adjust your weight according to the recommendations.
Turn the hips and shoulders in the direction of the movement. If you’ve already adjusted your weight correctly, now it’s time to turn your hips and shoulders in the direction you’re sliding.
Pay attention to safety, because pieces of stone, wood or glass on the road can easily sabotage your slide.
It’s time to knock out that rear leg. Kick in the direction you choose. He can turn you 180 degrees to complete the slide.
Tilt your body back on the slide, over and over again. Otherwise, if you lean forward, you can stop the board completely at a higher speed, which is not safe.
Lean forward after completing the slide. Turn 180 degrees and move around, lean forward to avoid falling. If you perform all the steps correctly, your board will slow down to the point where you want to slow down.
Method 3: Stopping while driving or moving on a rough surface.
If you drive at walking speed, you can get back up and grab the sign. Jump to the back of the board and when your board goes up, grab it with your hand.
Fly at walking speed, try to escape and run away. Run as fast as your board moves so you don’t fall off the board. Try not to drive more than 20 miles per hour.
Remember, this technique is risky because it can push your body away. He could have someone walk down the street or interrupt the driver. If you throw away the board to jump and slow down, you can avoid this situation.
Stop driving on a rough surface. While riding, move the longboard over a surface that is not smooth and rough enough to create friction. This makes your longboard slow and then stops. In this case, choose a road with pieces of grass or gravel on the side of the road.
Remember, you drive on short grass, you can drive fast. But if you roll in the thick grass, you can fall.
How do you slow down on a longboard?
The ability to slow down on a longboard is a prerequisite for longboarding. The reason is… :
If you ride on a longboard on a busy road or if you cross a road, you have to go slower.
To know how to slide, you have to slow down.
This way you avoid falls when doing tricks with advanced longboard techniques.
Slowing down on a longboard is a process we support before we stop. To slow down the longboard, just follow the end of the method that comes just before the stop.
If you want to experience an extraordinary journey on your favourite longboard, you need to know how to slow down and stop at the longboard. The technologically advanced braking system ensures a cool setting.
how to slow down on a longboard downhill,longboard hill stop
Disclosure: We are a professional review company & our reviews are not biased towards any of the products we review. We test each product thoroughly and give marks to only the very best that is given by our author. We are very independently owned & the opinions expressed here are our own. However, if you purchase anything after clicking the links present in the articles then we get some commissions for it which help maintaining the websites expenses like servers, security etc.